One Time Offers have limited quantities available and usually once they are sold out, they are not offered again.This gun features a tapered octagon barrel, steel frame, brass trigger guard, 6-shot cylinder, fixed sights and two-piece walnut grips.Howell Conversion Cylinders (sold separately) are for use with steel frame revolvers only.Features Tapered octagonal barrel Major Civil War side arm Different finishes and barrel lengths.
You can learn more about the cookies we use and why we use them by viewing our Privacy Policy. By continuing to use our site, you accept our use of cookies. These conversions, of course, being akin to the original Remington cartridge conversions used on the Western frontier of the 1860s and 1870s. They are commonly, though inaccurately, referred to as the Model 1858 due to the patent markings on its New Model barrels, PATENTED SEPT. E. REMINGTON SONS, ILION, NEW YORK, U.S.A.NEW MODEL.; although wide scale production did not start until 1861. Due to the fire, the Colt 1860 Army was not available for some time. Subsequently, large numbers of the Remington revolver were ordered by the U.S. It was more expensive, by 50 cents (a difference of more than US12 in 2013 dollars), than the Colt, but those who could afford it remarked on its durability. Remington Sons, Ilion, N.Y., based on the Fordyce Beals patent of September 14, 1858 (Patent 21,478). The Remington Army revolver is large-framed revolver in.44 caliber with an 8-inch barrel length. The Remington Navy revolver is slightly smaller framed than the Army and in.36 caliber with a 7.375 inch Beals Navy 7.5 inch barrel length. There were three progressive models made: the Remington-Beals Army Navy (18601862), the 1861 Army Navy (18621863), and the New Model Army Navy (18631875). The three models are nearly identical in size and appearance. Subtle but noticeable differences in hammers, loading levers, and cylinders help identify each model. S. Ordnance Department. Combustible cartridge velocities averaged from 700 to 900 feet per second (270 ms), depending on powder quality, charge and conical bullet weight. Combustibles were usually loaded with a special high performance sporting grade black powder, using the minimum charge required for a specified impact level, usually determined by pine penetration tests. The special powder and minimal charge reduced black powder fouling, allowing revolvers to be fired as much as possible before cleaning was necessary. The design is stronger and less prone to frame stretching than the Colt revolvers of the same era. While the Colt employs separate screws for the cylinder stop and trigger, those components share the same through-frame screw in the Remington design. A downside in the design of the 1858 is that the barrel and receiver are a single piece, making it more difficult to clean the barrel, as it cannot be removed. The milled slot positively secured the hammer between chambers for safe carry by placing the hammers firing pin where it did not rest on a percussion cap, eliminating the risk of an accidental discharge if the gun was dropped or the hammer struck. Most 19th-century revolver designs lacked such safety features. ![]() It was possible to lower the Whitney hammer between cylinder chambers for safe carry, but without the Remington milled slot, the Whitney cylinder could possibly slip and rotate, allowing the hammer to strike a loaded, capped chamber and cause an accidental discharge. It is, however, unlikely that this was common practice during the period. The Remington Army cartridge-conversions were the first large-caliber cartridge revolvers available, beating even Smith Wessons.44 American to market by nearly two years. Buffalo Bill Cody Gun Extant. Accompanying the sale of the pistol were personal artifacts of Codys including seventeen handwritten letters. The Euroarms and Uberti New Model Army replicas are nearly identical to the originals. These replicas are very popular in civil war reenacting and Cowboy Action Shooting. Several companies produce drop-in conversion cylinders for replicas, enabling the firing of low-pressure modern cartridges without altering the revolvers frame.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |